Our expertise
What we offer We provide multidisciplinary engineering and project development services across energy, transport, water, and civil infrastructure. Each assignment is shaped around real site conditions, technical requirements, regulatory compliance, environmental responsibility, and the objectives of the project.
Geodetic & Topographical & GIS Surveying, mapping, and spatial data services from field capture to legal cadastral support.
Learn more+ Topographic land surveys Photogrammetry and UAV (drone) surveys LiDAR and laser scanning surveys Hydrographic and bathymetric surveys Digital terrain modeling (DTM/DEM generation) Utility mapping (underground and above-ground infrastructure) Georeferencing and coordinate system transformations Contour mapping and elevation profiling Boundary and cadastral surveys Volume calculations (cut and fill, stockpiles) GIS mapping, spatial analysis, and data processing Legal support and consultancy for cadastral services Construction staking and site layout services As-built surveys and verification measurements Monitoring surveys (deformation, settlement, and displacement) Service page →
Geological / Geotechnical / Hydrological / Seismic Studies Ground investigation and hazard studies that underpin safe foundation and infrastructure design.
Learn more+ Geological mapping and site investigations Engineering geology assessments Soil classification and stratigraphy analysis Bearing capacity and foundation design recommendations Slope stability and landslide risk assessments Groundwater studies and hydrogeological investigations Hydrological analysis (surface water, drainage, flood risk assessment) Watershed and catchment area studies Erosion and sediment transport analysis Seismic hazard assessments Seismic site classification (site response analysis) Liquefaction potential analysis Ground motion and earthquake impact studies Environmental geology assessments Geotechnical monitoring (settlement, deformation, groundwater levels) Service page →
Architectural Services From concept and visualization to permit documentation and architectural oversight on site.
Learn more+ Concept design and architectural planning Schematic design development Detailed architectural design Preparation of architectural drawings (plans, sections, elevations) 3D modeling and architectural visualization (renderings) Urban design and site layout planning Industrial and Infrastructure Architecture Building code and regulatory compliance Preparation of technical documentation for permits Sustainable and energy-efficient design solutions and Certification Adaptive reuse of existing buildings Accessibility and universal design planning Construction documentation and detailing Site supervision and architectural oversight As-built documentation and reporting Service page →
Civil Engineering Services Structural, road, and infrastructure design with quantities, tender support, and site supervision.
Learn more+ Feasibility studies and technical assessments Structural design and analysis Design of roads and transportation infrastructure Highway and pavement design Foundation engineering and earthworks design Retaining structures and slope stabilization design Bridge and culvert design Infrastructure rehabilitation and upgrading Preparation of technical drawings and specifications Quantity take-offs and cost estimation Construction planning and scheduling Tender documentation and contract preparation Construction supervision and project management Quality control and site inspections As-built documentation and reporting Service page →
MEP (Mechanical, Electrical, Plumbing) Services Integrated building systems design — HVAC, power, plumbing, fire, and low-voltage — through to supervision.
Learn more+ HVAC (heating, ventilation, and air conditioning) system design Plumbing and sanitary system design Water supply and drainage system design Fire protection and firefighting system design and Certification Electrical power distribution design Lighting design (interior, exterior, and landscape) Low-voltage systems design (data, telecom, security, CCTV) Energy efficiency and sustainability solutions and Certification Renewable energy systems integration (e.g., solar PV) Earthing and lightning protection design Backup power systems (generators, UPS) Preparation of technical drawings and specifications Equipment selection and sizing Cost estimation and bill of quantities (BOQ) Supervision of MEP installations Service page →
Environmental Services Impact assessment, monitoring, permitting, and compliance aligned with national and IFC/EBRD standards.
Learn more+ Environmental impact assessment (EIA) Strategic environmental assessment (SEA) Environmental management plans (EMP) Environmental and Social Impact Assessments (ESIAs) (EBRD & IFC Standards) Environmental monitoring and reporting No Go areas identification Soil contamination assessment and remediation Waste management planning and solutions Hazardous materials assessment and management Environmental auditing and compliance review Climate change impact assessment and mitigation strategies Biodiversity and ecological studies Forest and Pasture management plans Environmental permitting and licensing support Risk assessment and environmental due diligence Service page →
HSE (Health, Safety & Environment) Services HSE systems, risk analysis, site audits, and safety-in-design across the project lifecycle.
Learn more+ HSE management systems development and implementation Occupational health and safety risk assessments Hazard identification and risk analysis (HIRA / HAZID / HAZOP) Preparation of HSE plans and procedures Construction site safety supervision and audits Incident investigation and reporting Emergency response planning and drills Workplace health and safety training Personal protective equipment (PPE) assessment and planning Safety inspections and compliance monitoring Fire safety planning and risk assessment Contractor HSE management and evaluation Safety-in-design (SiD) and risk elimination during design phase Preparation of HSE design criteria and technical specifications Design review and compliance with international HSE standards Service page →
Financial & Economical Services Feasibility, cost modeling, funding advisory, and economic analysis for investment decisions.
Learn more+ Financial feasibility studies Economic cost-benefit analysis Investment appraisal and project evaluation Budget planning and financial forecasting Cost estimation and cost control Capital expenditure (CAPEX) planning and optimization Operational expenditure (OPEX) analysis and management Life-cycle cost analysis (LCCA) Financial modeling and scenario analysis Funding strategy and financing advisory Public-private partnership (PPP) advisory Risk analysis and financial risk management Market analysis and economic studies Tariff and pricing analysis Cash flow analysis and management Service page →
Solar Energy Services Solar PV from resource assessment and design through bankability, commissioning, and O&M planning.
Learn more+ Solar resource assessment and site evaluation Feasibility studies for solar PV projects Technical due diligence for solar installations Conceptual and detailed design of solar PV systems Grid-connected and off-grid system design Hybrid systems (solar + battery) design Energy yield analysis and performance simulation System sizing and optimization Selection of photovoltaic panels, inverters, and components Bankability studies and investor support Installation supervision and quality control Testing, commissioning, and performance verification Operation and maintenance (O&M) planning Energy storage system (BESS) integration Legal, technical, institutional and permitting consultancy services Service page →
Transmission Lines & Substations Corridor studies, line and substation design, protection, SCADA, and permitting support.
Learn more+ Route selection and corridor optimization for transmission lines Load flow and electrical load calculations Tower spotting and structural design of transmission towers Foundation design based on geotechnical investigations Conductor, OPGW, and insulator selection and configuration Sag-tension calculations and line profiling Substation layout design Development of single-line diagrams (SLD) Busbar scheme design and equipment arrangement Power transformer and substation equipment sizing and selection Protection and control system design (relay schemes) SCADA and communication system design Grounding (earthing) system design for lines and substations Lightning protection and insulation coordination studies Legal, technical, institutional and permitting consultancy services Service page →
Wind Energy Wind resource, layout, electrical design, grid connection, and civil works for wind farms.
Learn more+ Wind resource assessment and energy yield analysis (WRA) Micro-siting and turbine layout optimization Electrical load calculations and power output estimation Wind turbine selection and technical specification Foundation design for wind turbines (geotechnical-based) Internal cable network (MV collection system) design Substation design for wind farm grid connection Grid interconnection and compliance studies Load flow, short-circuit, and stability analysis SCADA and communication system design Earthing and lightning protection system design Access roads and civil infrastructure design Noise impact and shadow flicker assessment (design considerations) Optimization of energy production and system efficiency Legal, technical, institutional and permitting consultancy services Service page →
Transportation (Roads) Traffic studies, geometric and pavement design, drainage, safety, and ITS for road projects.
Learn more+ Traffic studies and road capacity analysis Route alignment and corridor selection Topographic and geodetic survey integration Horizontal and vertical alignment design Road geometric design (curves, gradients, cross-sections) Pavement design (flexible and rigid pavements) Subgrade evaluation and geotechnical-based design Drainage and stormwater management design Intersection and interchange design Road safety design and traffic control measures Earthworks design (cut and fill optimization) Roadside infrastructure design (barriers, signage, markings) Urban road and street design (complete streets concept) Bridge and culvert design coordination Road lighting and intelligent transport systems (ITS) design Service page →
Water Supply Demand forecasting, treatment, networks, pumping, storage, and SCADA for water supply systems.
Learn more+ Water demand assessment and consumption forecasting Source identification and yield analysis (surface and groundwater) Hydraulic load calculations and system sizing Intake structure design (rivers, reservoirs, wells) Raw water transmission pipeline design Water treatment plant (WTP) process design Pumping station design and pump selection Storage facilities design (reservoirs, tanks, towers) Distribution network design and optimization Hydraulic modeling and pressure management Pipe material selection and sizing Leakage control and non-revenue water (NRW) reduction strategies SCADA and automation system design Firefighting system integration and demand planning System reliability, redundancy, and energy efficiency optimization Service page →
Wastewater Sewer networks, pumping, WWTP process design, sludge handling, and facility automation.
Learn more+ Wastewater flow estimation and load forecasting Sewer network layout and system planning Hydraulic design of gravity and pressurized sewer systems Pipe sizing, slope, and material selection Manhole and inspection chamber design Pumping stations and lift station design Wastewater treatment plant (WWTP) process design Preliminary, primary, secondary, and tertiary treatment design Sludge treatment, handling, and disposal system design Stormwater and combined sewer system considerations Inflow and infiltration (I&I) analysis and reduction strategies Odor control system design Effluent discharge compliance and environmental standards integration SCADA and automation systems for wastewater facilities System resilience, redundancy, and energy efficiency optimization Service page →
Irrigation Systems Crop water demand, network hydraulics, pumping, fertigation, and smart irrigation automation.
Learn more+ Irrigation water demand assessment and crop water requirements Soil analysis and infiltration rate evaluation Source identification and water availability analysis Irrigation method selection (drip, sprinkler, surface) Hydraulic design of irrigation networks Pumping systems design and equipment selection Canal and pipeline design (open channels and pressurized systems) Reservoirs and on-farm storage design Filtration and fertigation system design Irrigation scheduling and efficiency optimization Drainage system design for agricultural lands Erosion control and land grading design Automation and smart irrigation systems (sensors, controllers) Water conservation and efficiency strategies Operation, maintenance, and system sustainability planning Service page →
Hydropower Hydrology, civil works, electro-mechanical design, and grid connection for hydropower plants.
Learn more+ Hydrological assessment and flow duration analysis Site selection and feasibility studies Catchment area and watershed evaluation Hydraulic design of intake structures Headrace canal and tunnel design Surge tank and pressure shaft design Penstock design and material selection Powerhouse layout and structural design Turbine selection (Kaplan, Francis, Pelton) and sizing Generator and electro-mechanical equipment design Tailrace channel and discharge structure design Sediment management and desanding system design Dam and reservoir design (if applicable) Grid connection, substations, and transmission design SCADA systems, automation, and plant optimization Service page →
Tendering & Public Auction Services Tender docs, bid evaluation, procurement strategy, contract admin, and independent engineering.
Learn more+ Preparation of tender documentation (technical specifications, BoQs, drawings) Cost estimation and budgeting for projects Preparation of bidding documents and contract forms Technical and financial bid evaluation Prequalification of contractors and suppliers Procurement strategy development and advisory Contract administration and management Claims analysis and dispute resolution support Value engineering and cost optimization studies Project feasibility studies and advisory services Technical due diligence and project reviews Preparation of Terms of Reference (ToR) Assistance during tendering process and negotiations Compliance review with local and international standards Independent engineering and consultancy services Service page →
Project Management and Supervision Planning, QA/QC, cost control, HSE on site, commissioning support, and project documentation.
Learn more+ Project planning, scheduling, and resource management Preparation and monitoring of project timelines (CPM, Gantt charts) Construction supervision and site management Quality assurance and quality control (QA/QC) supervision Cost control, budgeting, and financial monitoring Contract administration and coordination with stakeholders Progress monitoring and reporting Risk management and mitigation planning Change order management and variation control Health, Safety & Environment (HSE) supervision during construction Coordination between design teams, contractors, and clients Review and approval of shop drawings and technical submittals Testing, commissioning, and project handover supervision Claims management and dispute resolution support Project documentation and record management Service page →
.png&w=256&q=75){kind=icon}
